|
Product Details:
|
| Material: | Galvanized Steel Or Stainless Steel Or Aluminum | Base Size: | 50mm X 50mm |
|---|---|---|---|
| Base Thickness: | 0.4mm | Pin Dia: | 12ga As Standard |
| Pin Length: | 2/1" To 12" | Self Locking Washer: | Washer And Domn Cap |
| Highlight: | insulation hangers,insulation pins and washers |
||
Introduction To Self Adhesive Insulation Pins
Self-adhesive hangers are designed to fix efficiently insulation on smooth surfaces such as air ducts, attenuators, chambers
and enclosures. It consists of a pin, firmly mounted on a high quality self-adhesive base.
After the self-adhesive hangers are installed, the insulation is impaled over the spindle & secured with a self-locking washer.
Specification Of The Self Adhesive Insulation Pins
Material:Galvanized Steel (Standard),Available in Stainless Steel & Alum as special order
| pin diameter | base plate size | insulatiion pin length |
| 12ga ( 0.106 " ) | 2 " square w / tape | 1 " |
| 12ga ( 0.106 " ) | 2 " square w / tape | 1 - 5 / 8 " |
| 12ga ( 0.106 " ) | 2 " square w / tape | 2 " |
| 12ga ( 0.106 " ) | 2 " square w / tape | 2 - 1 / 2" |
| 12ga ( 0.106 " ) | 2 " square w / tape | 3 - 1 / 2" |
| 12ga ( 0.106 " ) | 2 " square w / tape | 4 - 1 / 2" |
| 12ga ( 0.106 " ) | 2 " square w / tape | 5 - 1 / 2" |
| 12ga ( 0.106 " ) | 2 " square w / tape | 6 - 1 / 2" |
| 12ga ( 0.106 " ) | 2 " square w / tape | 8 " |
Other Details About The Self Adhesive Insulation Pins
Self Adhesive Insulation Pins Application:
Best results are obtained when ambient temperature is above 40° F at the time of application.
Remove the release paper from the base plate and apply hanger to a suitable flat surface.
A firm straight, forward pressure should be used. Do not twist. Due to the quick-tack nature of the adhesive, it is very important
that the release paper not be removed until ready to apply the hanger.
Insulation may be applied immediately after properly securing the hanger.
Hangers should be stored at 75° F and 50% relative humidity. It is important that stock be rotated. Shelf life is estimated at 2
years if stored as recommended
WIPE SURFACE CLEAN.Anchor should be applied to a clean, dry non-porous surface
PEEL OFF RELEASE BACKING.NOTE: Double faced foam tape has a one-year active shelf life
STICK ANCHOR IN PLACE.Select location before contact with surface.Press firmly
APPLY FIRM PRESSURE.20 pounds of pressure should be applied all around the base of the anchor
ALLOW TO STAND 15-20 MINUTES.This will permit better adhesion to take place
Package of Self Adhesive Insulation Pins
1. insulation pin length less than 65mm, 1000pcs per carton, 64 cartons per pallets.
2. insulation pins length 70mm-120mm, 500pcs per cartons,64 cartons per pallets.
3. insulation pins length 125mm-250mm, 250 pcs per cartons, 64 cartons per pallets.
4. as your requirement
Related Products
Perforated Base Insulation Hangers
The perforated base insulation hangers are designed to fix efficiently insulation concrete and any other rough surfaces.
It consists of a pin, firmly mounted on a perforated base.
Material:Galvanized Steel (Standard),Available in Stainless Steel & Alum as special order
| pin diameter | base plate size | insulation pin length |
| 12ga ( 0.106 " ) | 2 " square | 1 " |
| 12ga ( 0.106 " ) | 2 " square | 1 - 5 / 8" |
| 12ga ( 0.106 " ) | 2 " square | 2 " |
| 12ga ( 0.106 " ) | 2 " square | 2 - 1 / 2" |
| 12ga ( 0.106 " ) | 2 " square | 3 - 1 / 2" |
| 12ga ( 0.106 " ) | 2 " square | 4 - 1 / 2" |
| 12ga ( 0.106 " ) | 2 " square | 5 - 1 / 2" |
| 12ga ( 0.106 " ) | 2 " square | 6 - 1 / 2" |
| 12ga ( 0.106 " ) | 2 " square | 8 " |
| 12ga ( 0.106 " ) | 2 " square | 8 - 1 / 2" |
| 12ga ( 0.106 " ) | 2 " square | 9 - 1 / 2" |
| 12ga ( 0.106 " ) | 2 " square | 10 - 1 / 2" |
| 12ga ( 0.106 " ) | 2 " square | 12 " |
Contact Person: David
Tel: 86-18732199987
Fax: 86-1336-3891298
